Ecovacs Robot vacuum Common Problems
Find your problem in the list below. Each page explains the most likely causes, step-by-step checks you can do yourself, when to call a pro, and the parts that commonly resolve it. 119 problems covered.
Shop Ecovacs Robot vacuum parts at Amazon
All Robot vacuum codes across brands →
Finding your model number: it is on the underside label or in the app.
Deebot N10
All Ecovacs Deebot N10 codes & guides → (8 covered)
- DEEBOT cannot return to the Docking Station — The robot cannot find or reach its Docking Station to recharge.
- DEEBOT does not clean automatically at the scheduled time — A programmed cleaning time passes and the robot does not start.
- DEEBOT does not clean the whole area — The robot finishes without covering the whole cleaning area.
- DEEBOT gets stuck while working and stops — The robot becomes tangled or trapped and stops cleaning.
- DEEBOT is not charging — The robot is docked but not taking a charge.
- DEEBOT misses cleaning spots to be cleaned, or repeats cleaning the area cleaned — Some spots are skipped while other areas are cleaned more than once.
- DEEBOT returns to the Docking Station before it has finished cleaning — The robot goes back to recharge before the cleaning job is done.
- The water is not coming out of the Reservoir when DEEBOT is mopping — The mop stays dry because no water is reaching the mopping pad.
Deebot N8
All Ecovacs Deebot N8 codes & guides → (10 covered)
- AUTO Mode Button flashes RED — The indicator light and a voice report are how this DEEBOT announces a fault: a flashing red AUTO button means the robot has a problem.
- AUTO Mode Button glows a solid RED (low battery) — A solid red AUTO button means the robot's battery is low.
- DEEBOT cannot return to the Docking Station — The robot cannot find or reach its Docking Station to recharge.
- DEEBOT does not clean automatically at the scheduled time — A programmed cleaning time passes and the robot does not start.
- DEEBOT gets stuck while working and stops — The robot becomes tangled or trapped and stops cleaning.
- DEEBOT is making too much noise when cleaning — The robot is much louder than normal while cleaning.
- DEEBOT is not charging — The robot is docked but not taking a charge.
- DEEBOT misses cleaning spots to be cleaned, or repeats cleaning the area cleaned — Some spots are skipped while other areas are cleaned more than once.
- DEEBOT returns to the Docking Station before it has finished cleaning — The robot goes back to recharge before the cleaning job is done.
- The water is not coming out of the Reservoir when DEEBOT is mopping — The mop stays dry because no water is reaching the mopping pad.
Deebot Ozmo 930
All Ecovacs Deebot Ozmo 930 codes & guides → (8 covered)
- DEEBOT cannot return to the Docking Station — The robot cannot get back to its Docking Station.
- DEEBOT gets into trouble while working and stops — The robot gets tangled or trapped and stops mid-clean.
- DEEBOT is not able to connect to home Wi-Fi network — The robot cannot join the home Wi-Fi network.
- DEEBOT misses cleaning area — Parts of the cleaning area are skipped.
- DEEBOT returns to the Docking Station before it has finished cleaning — The robot heads back to recharge before the job is done.
- DEEBOT will not charge — The robot sits on the Docking Station but does not charge.
- DEEBOT will not clean automatically at scheduled time — A scheduled cleaning does not start.
- The water is not coming out of the Reservoir when DEEBOT is mopping — No water reaches the mop while mopping.
Deebot Ozmo T8
All Ecovacs Deebot Ozmo T8 codes & guides → (12 covered)
- AIVI Visual Detection Sensor cannot recognize objects — The AIVI camera sensor fails to identify objects in front of the robot.
- AUTO Mode Button flashes RED — The indicator light and a voice report are how this DEEBOT announces a fault: a flashing red AUTO button means the robot has a problem.
- AUTO Mode Button glows a solid RED (low battery) — A solid red AUTO button means the robot's battery is low.
- DEEBOT cannot return to the Docking Station — The robot cannot find or reach its Docking Station to recharge.
- DEEBOT does not clean automatically at the scheduled time — A programmed cleaning time passes and the robot does not start.
- DEEBOT gets stuck while working and stops — The robot becomes tangled or trapped and stops cleaning.
- DEEBOT is making too much noise when cleaning — The robot is much louder than normal while cleaning.
- DEEBOT is not able to connect to the home Wi-Fi network — The robot cannot join the home Wi-Fi, so app control fails.
- DEEBOT is not charging — The robot is docked but not taking a charge.
- DEEBOT misses cleaning spots to be cleaned, or repeats cleaning the area cleaned — Some spots are skipped while other areas are cleaned more than once.
- DEEBOT returns to the Docking Station before it has finished cleaning — The robot goes back to recharge before the cleaning job is done.
- The water is not coming out of the Reservoir when DEEBOT is mopping — The mop stays dry because no water is reaching the mopping pad.
Deebot T10
All Ecovacs Deebot T10 codes & guides → (12 covered)
- AIVI Camera cannot recognize objects — The AIVI camera fails to identify objects.
- DEEBOT Dual Side Brushes drop out of place during use — One or both dual side brushes come off while cleaning.
- DEEBOT gets stuck while working and stops — The robot becomes tangled or trapped and stops cleaning.
- DEEBOT is not able to connect to ECOVACS HOME App — App setup fails and the robot cannot be paired with the ECOVACS HOME App.
- DEEBOT is not charging — The robot is at the station but not charging.
- DEEBOT returns to the Station before it has finished cleaning — The robot goes back to the station before the job is done.
- Delay in remote control — App remote control of the robot responds slowly.
- During cleaning, DEEBOT appears in route disorder, running bias, repeated cleaning, small area leakage — The cleaning route looks disordered, the robot drifts, repeats areas or misses small areas.
- No signal found. Unable to return to the Station — The robot cannot find the station signal and cannot return to charge.
- Running is very loud during cleaning — The robot runs much louder than normal.
- Unable to create furniture map on App — The app cannot build the furniture map after cleaning.
- Video Manager cannot open or has no screen — The app's Video Manager will not open or shows no picture.
Deebot T20
All Ecovacs Deebot T20 codes & guides → (15 covered)
- Ash leakage occurs during working (dust leakage) — Dust leaks while the robot or station is working.
- DEEBOT does not respond to the Station instruction — The robot ignores commands from the OMNI Station.
- DEEBOT gets stuck while working and stops — The robot becomes tangled or trapped and stops cleaning.
- DEEBOT is not able to connect to ECOVACS HOME App — App setup fails and the robot cannot be paired with the ECOVACS HOME App.
- DEEBOT is not charging — The robot is at the OMNI Station but not charging.
- DEEBOT returns to the Station before it has finished cleaning — The robot goes back to the station before the job is done.
- Driving wheels are blocked — One or both driving wheels cannot turn.
- During cleaning, DEEBOT appears in route disorder, running bias, repeated cleaning, small area leakage — The cleaning route looks disordered, the robot drifts, repeats areas or misses small areas.
- Fail to enable Child Lock — Child Lock cannot be switched on.
- Mopping Pad Plates cannot rotate — The mopping pad plates will not spin.
- No signal found. Unable to return to the Station — The robot cannot find the station signal and cannot return to charge.
- The inner side of Dust Collection Cabin is dirty — Fine dust coats the inside of the OMNI Station's dust collection cabin.
- The map is lost — The saved home map disappears from the app.
- Unable to create home map on App — The app cannot create the home map.
- Voice prompt: the Cleaning Sink is full — When the water in the Cleaning Sink is full and cannot be drained out, the voice reports that the Cleaning Sink is full.
Deebot T9
All Ecovacs Deebot T9 codes & guides → (13 covered)
- AIVI Visual Detection Sensor cannot recognize objects — The AIVI camera sensor fails to identify objects in front of the robot.
- AUTO Mode Button flashes RED — The indicator light and a voice report are how this DEEBOT announces a fault: a flashing red AUTO button means the robot has a problem.
- AUTO Mode Button glows a solid RED (low battery) — A solid red AUTO button means the robot's battery is low.
- DEEBOT cannot return to the Docking Station — The robot cannot find or reach its Docking Station to recharge.
- DEEBOT does not clean automatically at the scheduled time — A programmed cleaning time passes and the robot does not start.
- DEEBOT does not clean the whole area — The robot finishes without covering the whole cleaning area.
- DEEBOT gets stuck while working and stops — The robot becomes tangled or trapped and stops cleaning.
- DEEBOT is not able to connect to the home Wi-Fi network — The robot cannot join the home Wi-Fi, so app control fails.
- DEEBOT is not charging — The robot is docked but not taking a charge.
- DEEBOT is stuck when cleaning with OZMO Pro installed — With the OZMO Pro oscillating mopping system fitted, the robot gets stuck.
- DEEBOT misses cleaning spots to be cleaned, or repeats cleaning the area cleaned — Some spots are skipped while other areas are cleaned more than once.
- DEEBOT returns to the Docking Station before it has finished cleaning — The robot goes back to recharge before the cleaning job is done.
- DEEBOT Side Brushes drop out of place during use — A side brush comes off while the robot is cleaning.
Deebot X1
All Ecovacs Deebot X1 codes & guides → (21 covered)
- After returning to the Station, DEEBOT does not empty the Dust Bin — The robot docks but auto-emptying does not start.
- AIVI Visual Detection Sensor cannot recognize objects — The AIVI sensor fails to identify objects in front of the robot.
- Ash leakage occurs during working (dust leakage) — Dust leaks while the robot or station is working.
- DEEBOT does not respond to the Station instruction — The robot ignores commands from the OMNI Station.
- DEEBOT gets stuck while working and stops — The robot becomes tangled or trapped and stops cleaning.
- DEEBOT is not able to connect to ECOVACS HOME App — App setup fails and the robot cannot be paired with the ECOVACS HOME App.
- DEEBOT is not charging — The robot is at the OMNI Station but not charging.
- DEEBOT returns to the Station before it has finished cleaning — The robot goes back to the station before the job is done.
- DEEBOT Side Brushes drop out of place during use — A side brush comes off while cleaning.
- Driving wheels are blocked — One or both driving wheels cannot turn.
- During cleaning, DEEBOT appears in route disorder, running bias, repeated cleaning, small area leakage — The cleaning route looks disordered, the robot drifts, repeats areas or misses small areas.
- Fail to empty the Dust Bin — Auto-emptying runs but does not empty the dust bin properly.
- Fail to enable Child Lock — Child Lock cannot be switched on.
- Mopping Pad Plate cannot rotate — The mopping pad plate will not spin.
- No signal found. Unable to return to the Station — The robot cannot find the station signal and cannot return to charge.
- Running is very loud during cleaning — The robot runs much louder than normal.
- The inner side of Dust Collection Cabin is dirty — Fine dust coats the inside of the OMNI Station's dust collection cabin.
- The map is lost — The saved home map disappears from the app.
- Unable to create furniture map on App — The app cannot build the furniture map after cleaning.
- Video Manager cannot open or has no screen — The app's Video Manager will not open or shows no picture.
- Voice prompt: the Cleaning Sink is full — When the water in the Cleaning Sink is full and cannot be drained out, the voice reports that the Cleaning Sink is full.
Deebot X2
All Ecovacs Deebot X2 codes & guides → (20 covered)
- After returning to the Station, DEEBOT does not empty the Dust Bin — The robot docks but auto-emptying does not start.
- AIVI Camera cannot recognize objects — The AIVI camera fails to identify objects.
- DEEBOT does not respond to the Station instruction — The robot ignores commands from the OMNI Station.
- DEEBOT gets stuck while working and stops — The robot becomes tangled or trapped and stops cleaning.
- DEEBOT is not able to connect to ECOVACS HOME App — App setup fails and the robot cannot be paired with the ECOVACS HOME App.
- DEEBOT is unable to charge — The robot is at the OMNI Station but not charging.
- DEEBOT returns to the Station before it has finished cleaning — The robot goes back to the station before the job is done.
- DEEBOT Side Brush drops out of place during use — The side brush comes off while cleaning.
- Delay in remote control — App remote control of the robot responds slowly.
- Disordered cleaning route, deviation from the cleaning route, repeated cleaning, or missing of small areas — While working, the route is disordered, the robot deviates, repeats cleaning or misses small areas (a large temporarily uncleaned area will…
- Driving wheels are blocked — One or both driving wheels cannot turn.
- Dust leakage occurs during working — Dust leaks while the robot or station is working.
- Fail to empty the Dust Bin — Auto-emptying runs but does not empty the dust bin properly.
- Mopping Pad Plate cannot rotate — The mopping pad plate will not spin.
- No signal found. Unable to return to the Station — The robot cannot find the station signal and cannot return to charge.
- Running is very loud during cleaning — The robot runs much louder than normal.
- The map is lost — The saved home map disappears from the app.
- Unable to create furniture map on App — The app cannot build the furniture map after cleaning.
- Video Manager cannot open or has no screen — The app's Video Manager will not open or shows no picture.
- Voice prompt: the Cleaning Sink is full — When the water in the Cleaning Sink is full and cannot be drained out, the voice reports that the Cleaning Sink is full.