Whirlpool Oven Error Codes
Find your code in the list below. Each page explains what the code means, the most likely causes, step-by-step fixes you can do yourself, and the parts that commonly resolve it. 37 codes covered.
Shop Whirlpool Oven parts at RepairClinic or Amazon
All Oven codes across brands →
Finding your model number: it is on the frame inside the oven door or behind the storage drawer.
4-digit F/E-code models (PartSelect chart)
All Whirlpool 4-digit F/E-code models (PartSelect chart) codes & guides → (19 covered)
- F1 E0 — EEPROM communication error: the oven control board cannot communicate with its memory. Official Whirlpool tech sheets list the same code as…
- F1 E1 — An electronic control fault: PartSelect lists it as an EEPROM checksum error, and Whirlpool tech sheets list it as an internal board…
- F1 E2 — UL A/D error on the oven control board - an internal analogue-to-digital conversion fault in the electronic control.
- F1 E3 — The wiring harness cavity size does not match the value stored in the control - the harness jumpers tell the board a different oven size…
- F1 E6 — Latch signal mismatch error on the oven control board - the latch signal the board receives does not match what it expects.
- F2 E0 — Shorted touch pad (keypad), in the PartSelect 4-digit chart.
- F2 E1 — Touch pad (keypad) cable unplugged, in the PartSelect 4-digit chart.
- F2 E5 — Cancel key line open: the control cannot read the Cancel key circuit on the touch pad.
- F3 E0 — The main oven temperature sensor is open or shorted (Whirlpool tech sheet wording). PartSelect's older table describes F3 E0 specifically…
- F3 E1 — An oven temperature sensor fault in the F3 E family: PartSelect groups all F3 E-codes as an oven temperature sensor (RTD) or warming drawer…
- F3 E2 — Oven temperature over 575F in Bake mode (too hot), in the older 4-digit tables.
- F3 E3 — Oven too hot in Clean mode - the newer companion to F3 E2 (too hot in Bake) and to the classic F2 code.
- F4 E1 — A meat probe defect: the control sees a problem with the meat probe, its receptacle, or the probe circuit.
- F5 E0 — Door and latch switches do not agree (Clean mode on tech sheets): for example the door reads open while the latch reads locked.
- F5 E1 — The self-clean door latch is not operating / will not lock: the door is not locked about a minute after the lock (self-clean) function…
- F5 E2 — A latch fault during Clean: the self-clean latch faulted while a clean cycle was running (grouped with F5 E0 / E1 as a door switch defect…
- F6 E0 — Return line not connected: the control loses the switch pulse return line and shows the code within about 60 seconds of power-up. On…
- F6 E1 — Over-temperature: Whirlpool sources list F6 E1 as oven over-temperature when heating / over-temperature in Cook, set when the oven reaches…
- F7 E1 — The common switch wire is defective: the common wire to the latch switch and door switch is shorted (to chassis ground or neutral on the…
Current models (Whirlpool Product Help)
All Whirlpool Current models (Whirlpool Product Help) codes & guides → (1 covered)
- F9 E0 — Miswired house or range (Whirlpool's current official meaning): the control detected a wrong electrical supply - incorrect wiring at the…
Current tech-sheet models (Whirlpool tech sheet W11503310)
All Whirlpool Current tech-sheet models (Whirlpool tech sheet W11503310) codes & guides → (3 covered)
- F2 E0 — Keypad disconnected, in current Whirlpool tech sheets.
- F2 E1 — Stuck / shorted key, in current Whirlpool tech sheets.
- F3 E2 — Warming drawer temperature sensor fault, in the current Whirlpool tech sheet W11503310.
Older 2-digit-code models
All Whirlpool Older 2-digit-code models codes & guides → (9 covered)
- F0 — Control board failure on older 2-digit-code ranges and wall ovens: the electronic oven control (clock) has failed its own checks.
- F1 — Control board failure on older 2-digit-code ovens; on some models a shorted keypad produces the same code. Newer ovens show this family as…
- F2 — Oven temperature too high: the control saw a temperature above its limit in Bake or in Clean. The newer equivalent is F3 E2 / F3 E3.
- F3 — Open oven temperature sensor circuit on older 2-digit-code ovens. On newer ovens the same fault is F3 E0.
- F4 — Shorted oven temperature sensor on older 2-digit-code ovens - the same sensor as F3 with the opposite failure. On newer ovens this is F3 E1.
- F5 — On older 2-digit-code ovens PartSelect lists F5 as a control board failure (the control's self-check / watchdog circuits disagree). Do not…
- F6 — On older code charts F6 is a problem in the time-keeping circuit of the electronic control. On newer tech sheets the F6 family is different…
- F7 — A function key is stuck or shorted on the keypad, on older 2-digit-code ovens. The newer equivalents are F2 E0 and F7 E1.
- F8 — Control board failure on older 2-digit-code ovens. Note: on some newer Whirlpool tech sheets F8 E-codes instead describe cooling fan speed…
Other codes & guides
- F9 — Platform-dependent: on older 2-digit-code ovens F9 is an oven door lock failure (self-clean latch switches not in the expected position).…
- Flashing clock — A flashing time of day on the display means the control detected a power failure - the same event PF reports on models that show letters.…
- LOC — Control Lock is activated (display may read LOC, Lock, Locked or show a padlock): the keypad ignores presses. It is a child-lock setting…
- PF — Power failure: the oven lost power and the clock needs resetting. It is an alert, not a part failure - PF with no known outage points at a…
- SAB — Sabbath Mode is activated (display may read SAB, Sab, 5AB or 5A6): the oven's display, tones and some functions are held for religious…