Polaris Pool cleaner Common Problems
Find your problem in the list below. Each page explains the most likely causes, step-by-step checks you can do yourself, when to call a pro, and the parts that commonly resolve it. 29 problems covered.
Shop Polaris Pool cleaner parts at Amazon
All Pool cleaner codes across brands →
Not sure of the code? Tap along with it
If your Polaris Pool cleaner blinks or beeps a pattern instead of showing a code, tap the button in time with each blink or beep. A pause longer than a second and a half starts a new group - we will match the rhythm to a code.
Your rhythm: -
Finding your model number: it is on the unit's rating plate.
FREEDOM
All Polaris FREEDOM codes & guides → (7 covered)
- Battery needs replacing (no error code) — FREEDOM cordless cleaner with no battery error code shown: if, when you remove the cleaner from the charging station, the battery indicator…
- Charging error (too cold) — On the FREEDOM cordless cleaner, charging pauses with a charging error when the temperature detected at the charging station is too cold —…
- Error 12 — iAquaLink app error 12 on the FREEDOM cordless cleaner: firmware update error.
- Error 14 — iAquaLink app error 14 on the FREEDOM cordless cleaner: motor block error. The manual directs owners to a retailer diagnostic — the motor…
- Error 20 & 21 — iAquaLink app errors 20 and 21 on the FREEDOM cordless cleaner: battery error — the battery block needs to be replaced.
- Error 22 & 23 — iAquaLink app errors 22 and 23 on the FREEDOM cordless cleaner: charging error — the temperature detected at the charging station location…
- Error 25 — iAquaLink app error 25 on the FREEDOM cordless cleaner: charging error caused by dirty charge plates, so the cleaner cannot charge properly…
Other codes & guides
- 1 flash — Status indicator flashing 1 flash / 1 second pause: communication error between the control box and the cleaner. On connected models the…
- 2 flashes — Status indicator flashing 2 flashes / 1 second pause: traction motor fault — right traction motor, left traction motor, or traction motor…
- 3 flashes — Status indicator flashing 3 flashes / 1 second pause: cleaner out of the water — the cleaner detects that it is not submerged.
- 5 flashes — Status indicator flashing 5 flashes / 1 second pause (iAquaLink control models only): software update failed or incomplete.
- Cable tangling in the pool — The floating cable tangles or coils in the pool while the cleaner runs, limiting its coverage.
- Cleaner not moving — The cleaner does not move at all when a cycle should be running.
- Connection error — The iAquaLink app shows a connection error — a red dot appears next to the robot in the "My systems" list — meaning the app cannot reach…
- Error 1 — Control-box display error 1: pump motor. The same alert appears in the iAquaLink app on connected models.
- Error 10 — Control-box display error 10: communication error between the control box and the cleaner.
- Error 11 — Control-box display error 11: sensor unit fault. This is not a user-serviceable fault — the manual directs owners to an approved service…
- Error 2 — Control-box display error 2: traction motor right. The same alert appears in the iAquaLink app on connected models.
- Error 3 — Control-box display error 3: traction motor left. The same alert appears in the iAquaLink app on connected models.
- Error 4 — Control-box display error 4: pump motor consumption — the pump motor is drawing abnormal current, usually because it is working against a…
- Error 5 — Control-box display error 5: drive motor consumption right — the right drive is drawing abnormal current.
- Error 6 — Control-box display error 6: drive motor consumption left — the left drive is drawing abnormal current.
- Error 7 — Control-box display error 7: cleaner floating — the cleaner is floating instead of staying on the pool surface/floor.
- Error 8 — Control-box display error 8: cleaner out of the water — the cleaner detects that it is not submerged.
- Error 9 — Control-box display 9: the cleaner has completed a cleaning cycle. Per the owner's manual this is not an error.
- Floating excessively — The cleaner does not stay on the pool surface/floor, or is floating excessively instead of hugging the bottom.
- Not cleaning the pool effectively — The cleaner runs but is not cleaning the pool effectively — debris is left behind or pickup is weak.
- Not climbing walls — The cleaner runs on the floor but is not climbing the walls.
- Rapid flashing — Status indicator rapid flashing: a software update is in progress. This is not an error.